Outdrives.Net     Mercruiser Sterndrive Information, Outdrive Information
Mercruiser Parts Mercruiser Help Mercruiser Manuals Mercruiser Tools Mercruiser Outdrives Contact


Transom Seal Kits

Your transom assembly is subject to severe stress and abuse even while
running under normal operating conditions.
A faulty transom component could sink your boat or cause other damage or injuries.

Have it inspected on a regular basis by a Certified Mercruiser Tech.

Please note that we also handle all the gimbal ring kits and update kits.

30-803097T1 Transom Seal Kit Alpha One
30-803097T1 Transom Seal Kit (Fits R, MR and Alpha One w/exh bellows) $263.00

30-803098T1 Transom Seal Kit Alpha w tube
30-803098T1 Transom Seal Kit (Fits R, MR and Alpha One w/tube) $280.00

30-803099T1 Transom Seal Kit Alpha Gen II
30-803099T1 Transom Seal Kit (Fits Alpha One Gen II) $300.00

30-803100T1 Transom Seal Kit Bravo
30-803100T1 Transom Seal Kit s/s to 8M0095485 (Fits Bravo and Blackhawk) $399.00.00


Replacing your Alpha One Bellows
Replacing your Alpha Gen II Bellows
Replacing your Bravo Bellows

DID YOU KNOW that Mercruiser now has a new style shift seal for the R, MR and Alpha One?
The shift shaft seal located in the bellhousing would fail and let water into
the shift cable pocket. This water would run up the cable and ruin it.
Open your engine compartment and look at your shift cable attaching plate.
Locate the cable that runs down to the drive and inspect the two side set screws.
These screws lock the core of the cable to the black plastic guide tube.
We sometimes refer to them as the "Frankenstien screws".
They are very small and have square heads.
Do the heads look all rusted?
If they are rusted chances are good that your shift shaft seal in your bellhousing
has failed and has allowed water to syphon up the cable.
Read much more about this at Replacing your Alpha One Shift Cable.

Mercury's solution was to improve the shaft seal design.
They now have a beefy brass bushing assembly which works well.
The Kit includes a new lever and set screw as well.
All you do is knock out the old seal and old guide bushing and tap
the new bushing into place with a little locktight.

45518T1 Bushing and Lever Kit
45518T1 Bushing and Lever Kit $55.00


Mercruiser Sterndrive Parts.
Pre-Alpha, R, MR and MC1 Parts
Alpha One Parts
Seal Kits
Alpha One Gimbal (Transom) Parts and Kits
Alpha Gen II Parts
Alpha Gen II Gimbal (Transom) Parts and Kits
Bravo One Parts
Bravo Two Parts
Bravo Three Parts
Bravo Gimbal (Transom) Parts and Kits
TR and TRS Parts
Transom Seal Kits
Gimbal Bearings
Shift Cable Kits
Gear Kits
Shift Interuptor Switch Kits
Anodes and Zinc Kits
Water Pump Kits
Power Trim Pump Kits and Trim System Parts
Decal Sets
Sterndrive Special Tools
Mercruiser shop Manuals
Propellers
Remote Controls
Gauges
Trim Sender Switches
Trim Cylinder Assemblies
Mercruiser Engine Parts
Filters and Filter Kits
Tuneup Kits
Carburetor Rebuild Kits
Carburetors
Raw Water Pump Kits
Circulation Water Pumps
Spark Plugs
Spark Plug Wire Kits
Gasket Sets
Exhaust Manifolds
Exhaust Elbows
Exhaust Riser Kits
Exhaust Water Shutter Kits
Ignition Modules and Ignition Coils
Cooling System Parts
Starter Motors
Solenoids
Alternators and Charging Systems
Belts and Belt-Pulley Kits
Drive Couplers
Fuel Pumps (Mechanical and Electric)
Wire Harnesses
Gauges and Instruments
Partial Engine Assemblies
Grease, Lubricants and Adhesives

©2004 Outdrives.Net •EmailAbout UsHomeReturn Policy Mercruiser HelpShop ManualsSearchContact

Note: We are NOT Mercury Marine or Mercruiser.